TESLA Smart Home

TESLA Smart Home Smart Smoke Sensor Zigbee

SKU: TSLZSEN-SMOKE

Quickstart

This is a Z-Wave Device for . To run this device please connect it to your mains power supply.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

With TESLA Smart Home Smart Smoke Sensor Zigbee, you don"t have to worry about your house turning into dust and ash. Its technology can detect danger in time and notify you via your phone or tablet. This allows you to quickly react to a detected problem and solve it.

A Clear App.
It is important to find out about a dangerous situation as quickly as possible. That"s why if the sensor detects smoke, it triggers an alarm and the smart app notifies you at the same time.

Reliability First.
The sensor TESLA Smart Sensor Smoke operates on the basis of the ZigBee system. This is a very stable protocol that, among other things, allows mutual communication between smart home features that also use the ZigBee protocol.

Range Of Up To 50 m.
The ZigBee system is known for its range of up to 50 m. This allows the sensor to cover every corner of your house.

Combines practicality with style.
The TESLA Smart Sensor Smoke will impress you not only with its minimalist design that fits into any interior, but also with its practical battery power supply. It only needs one battery to operate for a long time. And if the battery is low, it will automatically let you know that it needs to be replaced.

Communication via assistants.
The smart personal assistants Amazon Alexa and Google Assistant make the use of the sensor as well as other features of your smart home even more enjoyable. They can recognize your voice commands and pass them to the devices.

All in one app.
The sensor TESLA Smart Sensor Smoke is fully wireless and communicates with your smartphone or tablet via an app.

Detects false alarms.
That this indispensable feature of your home is really smart is also proved by the fact that it can"t be fooled. The smoke sensors inside the sensor are combined with heat sensors. If it detects smoke or an elevated temperature, it will automatically trigger an alarm.

Zigbee protocol.
The product belongs to a group that uses the ZigBee protocol by which the products communicate with each other. For the proper functioning of these products, it is necessary to have the TESLA Smart ZigBee Hub central unit as part of the smart home. This creates a common network for these products and allows them to interact with each other. For example, if the humidity sensor detects an increased value, it will automatically notify the dehumidifier via the TESLA Smart ZigBee Hub, which will start.

Features:

Smart Smoke Sensor Zigbee
ID: TSL-SEN-SMOKE
EAN: 8596115811058
Low Battery Notification: Yes
Alarm Sound Pressure: ? 80 dB / 3 m
Place of Installation: Ceiling
Power Supply: 1x button cell CR123A
Operating Temperature: -10?55 °C
Dimensions: Ø90 x 37 mm
Connectivity: Zigbee
App TESLA Smart: Google Android 6.0+, Apple iOS 11.0+

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

Make sure a device is in factory reset state before including. In doubt exclude before include.
If inclusion still fails, check if both devices use the same frequency.
Remove all dead devices from associations. Otherwise you will see severe delays.
Never use sleeping battery devices without a central controller.
Dont poll FLIRS devices.
Make sure to have enough mains powered device to benefit from the meshing

Technical Data

Dimensions	0.0900000x0.0900000x0.0370000 mm
Weight	87 gr
EAN	8596115811058
Frequency	XXfrequency
Maximum transmission power	XXantenna

Explanation of Z-Wave specific terms

Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
Inclusion — is the process of adding new Z-Wave devices into a network.
Exclusion — is the process of removing Z-Wave devices from the network.
Association — is a control relationship between a controlling device and a controlled device.
Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.